Cast Steel Bolted Bonnet Swing Check Valves

 

Dimensions & Weights


 
Cast Steel Bolted Bonnet Swing Check Valves - Dimensions

ASME Class 150

Fig. No. 180 external hinge pin 1½"-14", 18"-20", 36"
Fig. No. 184 internal hinge pin 16", 24", 30"


FEATURES
  • Full range of body/bonnet materials
  • Full range of trim materials
  • Anti-rotation disc
  • Flanged or butt weld ends
  • Full port design
  • Renewable seat rings seal welded
  • Horizontal or vertical service
  • Male and female bonnet joint
  • Corrugated metal bonnet gasket
  • Meet design requirements of ASME B16.25, B16.10 and ASME Section III

FIGURE NUMBERS: 180, 184

Dim Description VALVE SIZES (inches)
1.5 2 2.5 3 4 6 8 10 12 14 16 18 20 24 30
A Face to Face Flanged Ends in. 6.50 8.00 8.50 9.50 11.50 14.00 19.50 24.50 27.50 31.00 34.00 38.50 38.50 51.00 60.00
mm 165 203 216 241 292 356 495 622 699 787 864 978 978 1295 1524
A1 End to End Weld Ends in. 6.50 8.00 8.50 9.50 11.50 14.00 19.50 24.50 27.50 31.00 34.00 38.50 38.50 51.00 60.00
mm 165 203 216 241 292 356 495 622 699 787 864 978 978 1295 1524
A2 Face to Face RTJ in. 7.00 8.50 9.00 10.00 12.00 14.50 20.00 25.00 28.00 31.50 34.50 39.00 39.00 51.50 61.00
mm 178 216 229 254 305 368 508 635 711 800 876 991 991 1308 1550
K Center to Top Open in. 3.88 5.37 6.00 6.50 7.50 9.25 11.25 11.87 13.62 15.87 21.12 22.25 24.75 34.00 39.25
mm 98 137 152 165 191 235 286 302 346 403 536 565 629 864 997
  Weight Flanged Ends lbs 26 39 50 65 104 180 336 519 703 900 1175 1497 2370 4580 5900
kg 12 18 23 29 47 82 152 235 319 408 533 679 1075 2077 2667
  Weight Weld Ends lbs 20 32 43 58 87 150 258 392 550 700 940 1295 2144 4300 5400
kg 9 15 20 26 39 68 117 178 249 318 426 587 973 1950 2450

 

NOTE:

1. Dimensions, weights and other engineering data are subject to change or modification. This data is not to be used for construction unless confirmed
by the factory.

2. See Technical Data Section for Flow calculations (Cv).




ASME Class 300

Fig. No. 380 external hinge pin 1½" - 30"
Fig. No. 384 internal hinge pin 24” & 30”

 

FEATURES

  • Full range of body/bonnet materials
  • Full range of trim materials
  • Anti-rotation disc
  • Flanged or butt weld ends
  • Full port design
  • Renewable seat rings seal welded
  • Horizontal or vertical service
  • Male and female bonnet joint
  • Spiral wound bonnet gasket
  • Meet design requirements of ASME B16.5, B16.25, B16.10 and ASME Section III

 

FIGURE NUMBERS: 380, 384

Dim Description VALVE SIZES (inches)
1.5 2 2.5 3 4 6 8 10 12 14 16 18 20 24 30
A Face to Face Flanged Ends in. 9.50 10.50 11.50 12.50 14.00 17.50 21.00 24.50 28.00 33.00 34.00 38.50 40.00 53.00 62.75
mm 241 267 292 318 356 445 533 622 711 838 864 978 1015 1346 1594
A1 End to End Weld Ends in. 9.50 10.50 11.50 12.50 14.00 17.50 21.00 24.50 28.00 33.00 34.00 38.50 40.00 53.00 62.75
mm 241 267 292 318 356 445 533 622 711 838 864 978 1015 1346 1594
A2 Face to Face RTJ in. 10.00 11.13 12.13 13.13 14.63 18.13 21.63 25.13 28.63 33.63 34.63 39.13 40.75 53.88 63.75
mm 254 282 308 333 372 460 549 638 727 854 880 994 1035 1368 1619
K Center to Top Open in. 6.38 7.00 7.37 8.00 8.87 11.37 13.25 15.25 18.00 19.25 20.87 22.25 22.87 33.25 39.25
mm 162 178 187 203 225 289 337 387 457 489 530 565 581 845 997
  Weight Flanged Ends lbs 50 65 87 110 160 331 510 784 1280 1490 2032 2446 2980 4840 6600
kg 23 29 39 50 73 150 231 356 581 676 922 1110 1352 2195 2994
  Weight Weld Ends lbs 44 56 74 94 137 297 459 712 1176 1340 1855 2270 2735 4482 5700
kg 20 25 34 43 62 138 208 323 533 608 841 1030 1241 2033 2586

NOTE:

  1. Dimensions, weights and other engineering data are subject to change or modification. This data is not to be used for construction unless confirmed by the factory.
  2. See Technical Data Section for Flow calculations (Cv).



ASME Class 600

Fig. No. 680 external hinge pin 1½” - 20”

Fig. No. 684 internal hinge pin 14” & 20”

 

FEATURES

  • Full range of body/bonnet materials
  • Full range of trim materials
  • Anti-rotation disc
  • Flanged or butt weld ends
  • Full port design
  • Renewable seat rings seal welded
  • Horizontal or vertical service
  • Spiral wound bonnet gasket
  • Male and female bonnet joint
  • Meet design requirements of ASME B16.5 and B16.34

 

FIGURE NUMBERS: 680 & 684

Dim Description VALVE SIZES (inches)
1.5 2 2.5 3 4 6 8 10 12 14 16 20
A Face to Face Flanged Ends in. 9.50 11.50 13.00 14.00 17.00 22.00 26.00 31.00 33.00 35.00 39.00 47.00
mm 241 292 330 356 432 559 660 787 838 889 991 1194
A1 End to End Weld Ends in. 9.50 11.50 13.00 14.00 17.00 22.00 26.00 31.00 33.00 35.00 39.00 47.00
mm 241 292 330 356 432 559 660 787 838 889 991 1194
A2 Face to Face RTJ in. 9.50 11.62 13.12 14.12 17.12 22.12 26.12 31.12 33.12 35.12 39.12 47.25
mm 241 295 333 359 435 562 664 791 841 892 9914 1200
K Center to Top Open in. 7.52 9.76 12.13 14.37 16.14 18.31 20.08 22.09 24.33 38.74
mm 191 248 308 364 410 465 510 561 618 730
  Weight Flanged Ends lbs 80 100 135 152 280 550 910 1435 1892 2640 3480 5260
kg 36 45 61 69 127 2449 413 651 858 1198 1575 2386
  Weight Weld Ends lbs 60 86 120 125 225 486 783 1160 1570 2251 2890 4375
kg 27 39 54 57 102 220 355 526 712 1021 1310 1985

NOTE:

  1. Dimensions, weights and other engineering data are subject to change or modification. This data is not to be used for construction unless confirmed
    by the factory.
  2. See Technical Data Section for Flow calculations (Cv).



ASME Class 900

Fig. No. 984 internal hinge pin 3", 12"

 

FEATURES

  • Full range of body/bonnet materials
  • Full range of trim materials
  • Anti-rotation disc
  • Internal hinge pin
  • Flanged or butt weld ends
  • Full port design
  • Renewable seat rings seal welded
  • Horizontal or vertical service
  • Spiral wound bonnet gasket
  • Meet design requirements of ASME B16.5 and B16.34

 

FIGURE NUMBERS: 984

Dim Description VALVE SIZES (inches)
1.5 2 2.5 3 4 6 8 10 12
A Face to Face Flanged Ends in. USE CLASS1500
SWING CHECK VALVES
IN THESE SIZES
15.00 18.00 24.00 29.00 33.00 38.00
mm 381 457 610 737 838 965
A1 End to End Weld Ends in. 15.00 18.00 24.00 29.00 33.00 38.00
mm 381 457 610 737 838 965
A2 Face to Face RTJ in. 15.13 18.13 24.13 29.13 33.13 38.13
mm 384 460 613 740 841 968
K Center to Top Open in. 9.53 13.39 15.75 18.11 21.06 24.02
mm 242 340 400 460 535 610
  Weight Flanged Ends lbs 245 397 1128 1430 2170 3162
kg 111 180 512 649 984 1434
  Weight Weld Ends lbs 186 330 945 1174 1725 2625
kg 84 150 429 533 782 1191

NOTE:

  1. Dimensions, weights and other engineering data are subject to change or modification. This data is not to be used for construction unless confirmed by the factory.
  2. 2. See Technical Data Section for Flow calculations (Cv).




ASME Class 1500

Fig. No. 1584 internal hinge pin 1½" - 6"

 

FEATURES

  • Full range of body/bonnet materials
  • Full range of trim materials
  • Anti-rotation disc
  • Internal hinge pin
  • Flanged or butt weld ends
  • Full port design — API wall thickness
  • Renewable seat rings seal welded
  • Horizontal or vertical service
  • Spiral wound bonnet gasket
  • Meet design requirements of ANSI B16.5, B16.10, B16.34 and ASME Section III

 

FIGURE NUMBERS: 1584

Dim Description VALVE SIZES (inches)
2 3 4 6
A Face to Face Flanged Ends in. 14.50 8.50 21.50 27.75
mm 368 470 546 705
A1 End to End Weld Ends in. 14.50 18.50 21.50 27.75
mm 368 470 546 705
A2 Face to Face RTJ in. 14.63 18.63 21.63 28.00
mm 371 473 549 711
K Center to Top Open in. 9.57 11.81 11.81 15.91
mm 243 300 300 404
  Weight Flanged Ends lbs 230 380 590 1328
kg 104 172 268 602
  Weight Weld Ends lbs 173 307 460 1108
kg 78 139 208 503

NOTE:

  • Dimensions, weights and other engineering data are subject to change or modification. This data is not to be used for construction unless confirmed by the factory.
  • See Technical Data Section for Flow calculations (Cv).



Copyright © 2020 Crane Co. All Rights Reserved.